Unique Process

What is the Unique Process of Renaissance Technology?

What is so special about what we do? We have several unique processes that fundamentally differ from conventional battery chargers and motors.

Ideal Battery Charging
Common battery chargers push current from a source to a battery which over time causes damaging heat and degrading chemical processes that decrease the usable capacity in such batteries. The Renaissance process does just the opposite inside of the battery allowing for battery restoration, longevity and increased capacity. The patented charging process is cold (while the rejuvenation process, as totally distinguished from charging, will create some heat during that chemical process). The process triggers what some call a 'radiant' event in time which gives us many benefits. This is not to be understood as radiation but instead as used by Tesla and Bedini as a disruptive discharge carefully controlled with an acceptable method of capturing the benefits in a suitable load. While this may not define the nature of the energy in itself, we only intend to discuss the process in which we may benefit from it.

Higher Motor Efficiency and Impossible Charging Methods
Another benefit in the use of the Renaissance radiant process is in the area of efficiency. The battery charging may not only give you added efficiency in the fact that you can keep your batteries and restore many useless ones, but we have also discovered a way to make a motor into a battery charger at the same moment it performs its motor function, without the use of a generator system at all. A simple way to see this is with what has come to be called the SSG circuit on the monopole energizer system. The very simple circuit shows the batteries connected to each other in series, not in parallel, and never separated throughout the charging process. The primary battery powers the motor, while the charging battery can be more than ten times the voltage and capacity of the primary bank. The significance of the series charging shows the opposite of an amplifier system and nothing like an inductor, transformer or capacitor is used to store any charge to be later put into the charging battery bank. Therefore something other than the primary battery or motor coil is charging the battery. Any counter or back EMF resulting from the motor winding could only be insignificant and much less than the primary voltage of the battery anyway. So while the system allows for the proper gating of the BEMF to dramatically increase the motor efficiency, that alone cannot explain how a battery bank 100 times the size of the primary bank can be charged at all, or so fast. For example. When a 1 ohm resistor replaces the charging bank one can measure the insignificant current and voltage across it. This represents the BEMF or output of an energized motor coil. It cannot charge anything worth notice. Yet if one replaces that 1/2W resistor with a battery bank and is patient enough to let it charge (or first rejuvenate a battery that is 4 months old or older, which is not an efficient process) then one cannot account for the amount of charge in that battery over time. And this is Free Energy. All the energy used from the primary battery goes towards powering the motor and not towards charging batteries. And yet even more energy than this can be collected from this simple system without changing either the amount it takes to run the motor or the charge rate of the charging batteries.

Superior Motor Geometry
We have seen that the Renaissance process allows for ideal battery charging for battery longevity, rejuvenation and capacity increase. Secondly, our processes can remove the BEMF in motor systems to allow for higher efficiencies. Thirdly, our charging motor systems allow for charging of larger battery banks of a great range of voltage when motors are not supposed to be chargers at all. Now fourthly, our unique permanent magnet motor designs allow for an even greater added efficiency which can also add to a secondary charging process that sometimes is used to keep the primary source charged. This is proper geometry which does not fight against the forces of nature, but rather works with them to give us what we want.

This is just the Beginning
There are many other more advanced or related processes that we use which are too numerous to mention on this page. Each process is environmentally beneficial and saves people money. In many ways our systems produce opposite results of conventional technology and thus it is often hard for people to get used to them. It is often hard for engineers to evaluate the technology as it is outside of their training and experience, and the meters they use are mostly unsuited for testing in the ways they have been taught to use them.

Education Without Prejudice
So part of our our Unique Process is to teach all people to examine carefully their presuppositions and be willing to really see what is available to them in the environment around them. From simple patience in investigation and avoidance of ignoring lessons learned in supposed bad results, to encouraging people to experiment beyond what they thought was even possible, we inspire people in the scientific method to really become scientific and practical.

Learn by Experimentation and Help each other
Finally, the only way to really learn what we are talking about is to begin to experiment. Renaissance Charge has worked night and day to help you do this. We have made this an open source technology so that we can all learn together and benefit each other. We desire to expand our capabilities in this way and seek your support in buying our products and attending our Conventions. Together we can see a brighter future where batteries do not have to be replaced, and costs of energy are merely in the making of the machines, and where pollution is a memory of the past.